Link RTD Sensors and Digital Outputs to Ethernet Networks
The ioLogik E2260 is designed for system integrators to
acquire and
control remote RTD sensors over TCP/IP and Ethernet networks. Types of
RTD sensors include PT, JPT, Ni types, and resistor. The ioLogik E2260
supports Ethernet and can run multiple protocols, such as Modbus/TCP,
SNMP, HTTP, TCP, and UDP at 100 Mbps for high speed data acquisition.
Data can be distributed to up to 10 host computers.
Independent Configurations for Multiple RTD Channels
Each fixed physical RTD input can be independently configured by
software to PT, JPT, Ni, and resistor modes. In addition, a special
virtual channel can be configured by software to Average or Deviation
mode to calculate its fixed RTD channel.
LAN | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
Mechanical Specifications | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
Environment | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
Power Requirements | |
Power Consumption | 95 mA @ 24 VDC |
Power Input | 24 VDC nominal, 12 to 36 VDC |
Serial Communication Parameters | |
Flow Control | None |
Protocol | Modbus/RTU |
Data Bits | 8 |
Parity | None |
Stop Bits | 1 |
Baudrate | 1200 to 115200 bps |
Inputs and Outputs | |
Digital Outputs | 4 channels |
RTD Inputs | 6 channels |
LAN | |
Protection | 1.5 KV magnetic isolation |
Ethernet | 1 x 10/100 Mbps, RJ45 |
Protocols | Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP, CGI, SNTP |
RTD Inputs | |
Input Impedance | 625K ohms (min.) |
Sampling Rate | 12 samples/sec (all channels) |
Resolution | 0.1°C or 0.1 ohm |
Accuracy | ±0.1% FSR @ 25°C ±0.3% FSR @ -10 and 60°C |
Input Type | Pt, JPt, Ni, RTD sensor, resistor |
Environmental Limits | |
Operating Temperature | -10 to 60°C (14 to 140°F) |
Storage Temperature | -40 to 85°C (-40 to 185°F) |
Ambient Relative Humidity | 5 to 95% (non-condensing) |
Physical Characteristics | |
Weight | under 250 g |
Dimensions | 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in) |
Wiring | I/O cable max. 14 AWG |
Standards and Certifications | |
EMI | FCC Part 15 Subpart B Class A, EN 55022 Class A |
Safety | UL 508 |
Shock | IEC 60068-2-27 |
Vibration | IEC 60068-2-6 |
EMS | IEC 61000-4, IEC 61000-6 |
Freefall | IEC 60068-2-32 |
Digital Output | |
Type | Sink |
Isolation | 3K VDC or 2K Vrms |
Pulse Output Frequency | 100 Hz |
Over-temperature Shutdown | 175°C |
Over-voltage Protection | 45 VDC |
Current Rating | 200 mA per channel |
I/O Mode | DO or Pulse Output |
Over-current Protection | 2.6 A (4 channels @ 650 mA) |
Serial Communication | |
Interface | RS-485-2w: Data+, Data-, GND |
Serial Line Protection | 15 KV ESD for all signals |
MTBF (mean time between failure) | |
Time | 327,282 hrs |
Database | Telcordia (Bellcore) |
Warranty | |
Warranty Period | 5 years |
Details | See www.moxa.com/warranty |