Improve system efficiency via real-time data acquisition
Unlike traditional passive remote I/O, Active Remote I/O provides Active I/O messaging that can send message over Ethernet, TCP/IP network on I/O input status changes or meets certain condition, the message is sent to host computer. Communication between the host computer and Active Remote I/O device is concise and efficient. In addition, the message delivery time is 20 times faster than traditional SCADA systems (50 ms compared to 1 sec).

No programming! Hassle-free Click&Go™ logic control
Click&Go™ logic is the key to make ioLogik E2000 series become an intelligent remote I/O. Click&Go™ logic lets you decide when to send I/O data, and what to say to host computers for simple alarm control and messaging.

As opposed to using C-language or PLC-ladder, a person who understands basic logic concepts can do the configuration themselves, and easily finish their projects. Unlike passive remote I/O architecture, you can integrate Active Remote I/O’s input signals into one event to be an integrated message, and set up local output control at the same time. The unique Click&Go™ logic is a patent pending technology developed by Moxa.

Unique LCD Display Module for on-site configuration
ioLogik E2000 series Active Remote I/O provides an optional LCD display module for on-site management and configuration. The unique display module can display network and I/O settings, e.g. analog input value, digital input counter value. The IP, netmask address can be set locally without carrying a PC.

Independent Configuration for Multi-functional DI and DO points
Each digital input can be configured independently for DI or Event Counter mode, and each digital output can be independently configured for DO or Pulse Output mode.

Typical Application

Features

Actively transfer I/O data in real-time over Ethernet

Easy-to-use Click&Go™ Logic for local output control and messaging

12-point 24VDC digital input with DI/Event counter 8 points 24VDC digital output as pulse output 10/100Mbps Ethernet with Modbus/TCP protocol Connecting up to 10 hosts SNMP to I/O mapping that works with Network Management System Quick programming library for VB, VC, BCB

Specifications

LAN

Ethernet 10/100 Mbps, RJ45 Protection 1.5 KV magnetic isolation Protocol Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for I/O and Network), HTTP, SNTP,Active I/O Messaging, IP filtering

Serial

Interface RS-485 (2-wire): Data+, Data-, GND Serial Line Protection 15 KV ESD for all signals

Serial Communication Parameters

Parity None Data bits 8 Stop bits 1 Flow control None Speed 1200 bps to 115200 bps Protocol Modbus/RTU Built-in RTC Yes

Power Requirements

Power input 24 VDC nominal, 12 to 48 VDC Power consumption 282 mA @ 24 VDC (typ.) Field power 24 VDC nominal, up to 48 VDC

Mechanical Specifications

Wiring I/O cable max. 14 AWG

Environmental

Operating temperature -10 to 60°C (14 to 140°F), 5 to 95% RH Storage temperature -40 to 85°C (-40 to 185°F), 5 to 95%RH Vibration IEC60068-2-6

Digital Input

Inputs 12, source type I/O Mode DI or Event Counter (up to 900 Hz) Dry Contact Logic 0: short to GND, Logic 1: open Wet Contact Logic 0: 0 to 3 VDC, Logic 1: 10 to 30 VDC (DI COM to DI) Common type 12 points / 1 COM Isolation 3000 VDC

Digital Output

Outputs 8, sink type I/O Mode DO or Pulse output (up to 1 KHz) On-state voltage 24 VDC nominal Output current rating Max. 200 mA per channel Optical isolation 3K VDC Protection Over temperature shutdown: Min. 170°C Over current limit: typ. 750 mA/channel

Agency Approvals

EMI FCC Part 15, CISPR (EN55022) Class A EMS IEC61000-4-2 (ESD), level 2/3 IEC61000-4-3 (RS), level 2 IEC61000-4-4 (EFT), level 2 IEC61000-4-5 (Surge), level 3 IEC61000-4-6 (CS), level 2 IEC61000-4-8 (PM), level 1 IEC61000-4-11 (Dip) Safety UL 508 (pending) Shock IEC60068-2-27 Freefall IEC60068-2-32 Warranty 2 years

Specification