Improve system efficiency via real-time data acquisition
Unlike traditional passive remote I/O, Active Remote I/O provides Active I/O messaging that can send message over Ethernet, TCP/IP network on I/O input status changes or meets certain condition, the message is sent to host computer. Communication between the host computer and Active Remote I/O device is concise and efficient. In addition, the message delivery time is 20 times faster than traditional SCADA systems (50 ms compared to 1 sec).

No programming! Hassle-free Click&Go™ logic control
Click&Go™ logic is the key to make ioLogik E2000 series become an intelligent remote I/O. Click&Go™ logic lets you decide when to send I/O data, and what to say to host computers for simple alarm control and messaging.

As opposed to using C-language or PLC-ladder, a person who understands basic logic concepts can do the configuration themselves, and easily finish their projects. Unlike passive remote I/O architecture, you can integrate Active Remote I/O’s input signals into one event to be an integrated message, and set up local output control at the same time. The unique Click&Go™ logic is a patent pending technology developed by Moxa.

Unique LCD Display Module for on-site configuration
ioLogik E2000 series Active Remote I/O provides an optional LCD display module for on-site management and configuration. The unique display module can display network and I/O settings, e.g. analog input value, digital input counter value. The IP, netmask address can be set locally without carrying a PC.

Independent Configuration for Multi-functional AI and AO points
Each analog input can be independently configured by voltage or current mode by software. The analog input channels support various signals ranging from +/-150 mV to +/-10V at 16-bit resolution.

Typical Application

Actively transfer I/O data in real-time over Ethernet

Easy-to-use Click&Go™ Logic for local output control and messaging

8-channel analog input for mV, voltage, current signal with wire-off detection (at 4-20mA) 2-channel analog output for voltage, current actuator control Connecting up to 10 hosts SNMP to I/O mapping that works with Network Management System Quick programming library for VB, VC, BCB NIST-traceable calibration

LAN

Ethernet 10/100 Mbps, RJ45 Protection 1.5 KV magnetic isolation Protocol Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for I/O and Network), HTTP, Active I/O Messaging, IP filtering

Serial

Interface RS-485 (2-wire): Data+, Data-, GND Serial Line Protection 15 KV ESD for all signals

Serial Communication Parameters

Parity None Data bits 8 Stop bits 1 Flow control None Speed 1200 bps to 115200 bps Protocol Modbus/RTU Built-in RTC Yes

Power Requirements

Power input 24 VDC nominal, 12 to 48 VDC Power consumption 282 mA @ 24 VDC (typ.) Field power 24 VDC nominal, up to 36 VDC

Mechanical Specifications

Wiring I/O cable max. 14 AWG

Environmental

Operating temperature -10 to 60°C (14 to 140°F), 5 to 95% RH Storage temperature -40 to 85°C (-40 to 185°F), 5 to 95%RH Shock IEC60068-2-27 Freefall IEC60068-2-32 Vibration IEC60068-2-6

Analog Input

Inputs 8 Resolution 16-bit Input range +/-150 mV, +/-500 mV, +/-5 V, +/-10 V, 0 to 20 mA, 4 to 20 mA Data format 16-bit integer (2's complement) Accuracy +/- 0.1%, FSR @ 25°C, +/- 0.3%, FSR @ 0, 60ºC Optical isolation 3K VDC Sampling rate 10 samples/sec (voltage), 6 samples/sec (current) Input impedance 900K Ohm Built-in resistor for current input 125 Ohm Overvoltage Can withstand continuous overvoltage (protection range-10V to 10V)

Analog Output

Outputs 2 Resolution 12-bit Output range 0 to 10V, 4 to 20 mA Drive voltage 15 VDC for current output Data format 16-bit integer (2's complement) Accuracy +/- 0.1%, FSR @ 25C, +/- 0.3%, FSR @ 0, 60ºC (current) +/- 0.2%, FSR @ 25C, +/- 0.4%, FSR @ 0, 60ºC (voltage) CMR @ 50/60 Hz 95 dB min. Zero drift +/- 9μV/ºC Span drift +/- 25 ppm/ºC Load resistor < 250 Ohm

Agency Approvals

EMI FCC Part 15, CISPR (EN55022) Class A EMS IEC61000-4-2 (ESD), level 2/3 IEC61000-4-3 (RS), level 2 IEC61000-4-4 (EFT), level 2 IEC61000-4-5 (Surge), level 3 IEC61000-4-6 (CS), level 2 IEC61000-4-8 (PM), level 1 IEC61000-4-11 (Dip) Safety UL 508 (pending) Warranty 2 years

Specification